Installation instructions for the SCD2 Series Air Quality Sensors, protocol versions for BACnet and Modbus.

Installation instructions for the SHD2 Series Humidity Sensors, protocol versions for BACnet and Modbus.

SPW Differential Wet Pressure Transmitters utilise well proven ceramic technology. They have a low sensitivity to change in temperature and a high resistance to extreme temperatures. Total of linearity, hysteresis and repeatability ±1.25% fs max. in accordance with DIN EN 60770-1. Supplied complete with mounting bracket, screws and female connector with seal.

The STP300 is an electronic immersion temperature transmitter that converts a measured temperature into an electronic current signal of 4 to 20 mA. The STP300 is designed for immersion mounting in pipe systems with a separate pocket/well. The pocket/well is sealed, making it easy to replace the transmitter if necessary. The transmitter is intended for measurement of high and low temperatures. The transmitter is connected with a 2-wire cable, which serves both as power supply and for signal transmission. The reading of the measured signal is done over an external load resistance.

SpaceLogic SCD2 Series Air Quality Sensors are duct mount all-in-one sensors for monitoring air quality. The device combines CO2, temperature, humidity, VOC and particulate matter (PM) sensing into a single unit to ensure a building’s optimum air quality and energy efficiency. Each device is an active sensor that converts a measurement into one of the following output options: • Analog output: 4-20 mA, 0 to 5 Vdc or 0 to 10 Vdc • Protocol output: BACnet MS/TP, Modbus RTU As an integral part of Schneider Electric EcoStruxture Building Operation (EBO) software, the SCD2 protocol models’ Ready-Connect feature enables a plug & play experience for easy integration and configuration. Different models are available based on application requirements for lower-cost installations. SCD2 is available with an LCD display option on select models.

STD400 is an electronic average temperature transmitter that converts the average measured temperature into one electric current signal 4…20 mA. The transmitter is used for temperature measurement in air ducts.

The STO300 is an electronic temperature transmitter that converts the measured value into an analogue electrical signal of either 4 ... 20 mA or 0...10 V (field selectable). The transmitter is supplied as a complete unit, comprising the sensing element and amplifier mounted within a plastic enclosure, complete with circular cover resistant to ultraviolet light. The transmitter is intended for mounting on an outside wall, on the north side where possible. Electrical connection is via 2 or 3-wire cable, dependent on the output signal type selected. The temperature measurement range is field selectable to meet most application needs.

Product Announcement PA-01025 EasyLogic CP-Series IAQ Sensors - redefining healthy buildings using cost-effective solutions

EasyLogic CP-Series Indoor Air Quality Sensors

The STD660 is a revolutionary control solution for today’s applications. The adjustable probe length enables the user to find the best monitoring position with ease. This sensor is designed for use with Satchwell controllers to provide temperature control in ventilation systems.

The STP500 is designed for immersion mounting in pipe systems with a separate pocket (well). The pocket is closed in the bottom, making it easy to replace the sensor, if necessary.

Order form for available Temperature Calibration Certificates and Humidity/Pressure Calibration Certificates. Certificates available only when ordered at the same time as a sensor. The sensors will be ordered as normal, and the calibration will appear as a separate item/charge.

A summary of the Intelligent Devices EasyLogic Sensors

SLXRH Generation 2 Replacement Humidity Sensors and T2 Series Temperature only or Temperature and Humidity sensors work with SCD2, SHD2 and SHO2 Series Plant Room Sensors (with humidity and temperature options). These sensors use on-board RH sensor and solid state temperature sensors to be used on analog transmitters or protocol models. The sensors are factory calibrated and offered in various configurations based on the end application need. When a replacement is installed into the socket, the reading from the replacement sensor is used. The replacement sensor can subsequently be replaced as needed. SLXRH Series Generation 2 Replacement Humidity Sensors also work with the SLA and SLP Series Living Space Sensors (with humidity option). The SLA and SLP Series sensors use an onboard RH sensor. When a replacement sensor is installed into the socket on the SLA or SLP, the reading from the replacement sensor is used. The replacement sensor can subsequently be replaced as needed.

Installation instructions for the SCD2 Series Air Quality Sensors, analog versions.

SpaceLogic SHD2 Series Humidity Transmitters provide an ideal solution for measuring relative humidity in a wide range of conditions. All models are equipped with a solid state capacitive humidity sensor that is easy to replace in the field and a solid state temperature sensor for high accuracy measurements. SHD2 is an all-in-one device combining humidity and temperature sensing. Intended for duct mount applications, the device ensures a building’s optimum temperature and humidity levels, resulting in greater energy efficiency. Each device is an active sensor that converts a humidity or temperature measurement into 4-20 mA, 0 to 5 Vdc or 0 to 10 Vdc analog output. Different models are available based on application requirements for lower-cost installations.

SpaceLogic SHO2 Series Humidity Transmitters provide an ideal solution for measuring relative humidity in a wide range of humidity conditions. All models are equipped with a solid state capacitive humidity sensor that is easy to replace in the field. The housing is weatherproof and intended for outdoor mounting. The SHO2 is an all-in-one device combining humidity and temperature sensing. The device ensures a building’s optimum temperature and humidity levels, resulting in greater energy efficiency. Each device is an active sensor that converts a humidity or temperature measurement into an analog output: current output (4-20 mA) or voltage output (0 to 5 Vdc or 0 to 10 Vdc). Different models are available based on application requirements for lower-cost installations.

The SHD2 series comprises duct mount all-in-one sensors for monitoring humidity and temperature. SHO2 is the outdoor version of the combined next generation of the humidity and temperature sensor. By combining the humidity and temperature measurement in a single device, it ensures optimal precision in HVAC control. The SPM sensor is a new addition to the duct and plant room offer portfolio. It is a standalone sensor that measures Particulate Matter (PM) either through duct or outdoor installation

The CP-AI-C2-SE is a duct-mount CO2 transmitter designed for environmental monitoring and HVAC control applications. This device is ideal for commercial, industrial and general buildings, ensuring air quality and energy efficiency. Each device features an active sensor that converts a measurement into an analog output: 4-20 mA or 0 to 10 Vdc. This sensor is ideal for: • HVAC system control for improved comfort and energy savings • Hospitals, schools, museums and other workplaces requiring air quality control